• Filter by
Clear filters and search
08/04/2020

MasterEmaco N 303_TDS.pdf

Fire resistant gypsum based mortar material ... Load bearing 2.5k N/m2 UDL ... Acoustic Performance 47 dB reduction at 100 mm ... Max Unsupported Span 700 mm (Consult BASF for larger spans ...

  • pdf, 152.12 Kb
08/04/2020

MasterProtect 1840_TDS.pdf

High build phenol novolac epoxy liner for applications where high chemical & abrasion resistance are required ... Final cure 7 days @ 25°C ... Compressive Strength 8 hours >40 N/mm 2 ...

  • pdf, 153.20 Kb
08/04/2020

MasterSeal 505_TDS.pdf

MasterSeal 505 can be mixed with either a clean rod or gloved hand to the desired consistency ... Mix only the quantity which can be used immediately ... Hardened MasterSeal 505 can only be ...

  • pdf, 145.00 Kb
08/04/2020

MasterFlow 648_TDS.pdf

- Precision alignment of compressors, generators, pumps, fans and electric motors - Soleplates - Crane rail grouting - Grouting of rolling, stamping, grinding, crushing, drawing and ...

  • pdf, 179.61 Kb
08/04/2020

MasterProtect 1891_TDS.pdf

High build epoxy resin mortar, specifically designed for vertical and overhead applications ... Service temperature limits: -20°C to 65°C ... limits: 8°C to 45°C ... Pot life at 25°C 120 mins ...

  • pdf, 144.21 Kb
08/04/2020

MasterProtect P 1801_TDS.pdf

Phenol Novolac Epoxy Amine Cured Primer ... Mixed density at 25°C 1.15g/cm³ ... Initial cure 24 hours @ 25°C ... Final cure 7 days @ 25°C ... Concrete must be cured for 28 days ...

  • pdf, 145.89 Kb
08/04/2020

MasterProtect 1820_TDS.pdf

Phenol Novolac Epoxy Amine Cured High Build Coating ... Mixed density at 25°C : 1.173g/cm³ ... Initial cure 24 hours @ 25°C ... Final cure 7 days @ 25°C ... MasterProtect 1820 is supplied in 4 liter ...

  • pdf, 147.67 Kb
08/04/2020

MasterCast 121_TDS.pdf

Multi-purpose adhesive, surface sealer, primer and bonding agent, admixture for mortar ... As a bonding agent for cement screeds and renderings, plaster, etc ... Keep in place for a minimum ...

  • pdf, 151.71 Kb
08/04/2020

MasterFlow 936 AN_TDS.pdf

- Fixings close to free edges - Fire tested - Versatile - Anchoring without expansion pressure - High load capacities - Available in side-by-side cartridges (385ml) (585ml ...

  • pdf, 260.57 Kb
08/04/2020

MasterEmaco N 907_TDS.pdf

Two component polymer modified fairing coat and re-profiling mortar ... Total: 21.66kg or 12 liter packs ... Surfaces to receive MasterEmaco N 907 should be sound, clean and uncontaminated ...

  • pdf, 145.21 Kb
08/04/2020

MasterEmaco N 202_TDS.pdf

A single component cementitious blowhole filler and levelling mortar for cosmetic repairs, and surface leveling to new construction ... It is recommended that only full bags of 25 kg ...

  • pdf, 145.45 Kb
08/04/2020

MasterProtect FL 100_TDS.pdf

The technical information and application advice given in this BASF publication are based on the present state of our best scientific and practical knowledge ...

  • pdf, 136.25 Kb
08/04/2020

MasterFinish RL 225_TDS.pdf

MasterFinish RL 225 reacts chemically with cement to impart excellent release properties to treated surfaces ... Concrete cast against surfaces coated with MasterFinish RL 225 exhibit ...

  • pdf, 141.22 Kb
08/04/2020

MasterBrace ADH 2200_TDS.pdf

High strength, non-flow, epoxy bedding and repair ... resistant.̵ Non shrink.̵ Epoxy based.̵ Trowels to a smooth finish.̵ Easy to use.̵ Supplied in pre-weighed units.̵ No bonding ...

  • pdf, 161.28 Kb
08/04/2020

MasterBrace ADH 8900_TDS.pdf

Single-component polyurethane-based adhesive to bond TPO/FPO and PVC-P membranes ... Stocking period in original tank, sealed and at room temperature, 5 months ...

  • pdf, 140.74 Kb
08/04/2020

MasterBrace ADH 1414_TDS.pdf

Epoxy bonding agent for concrete repairs, bonding concrete to concrete, steel and granolithic toppings ... floor hardeners, oil, grease, fat, bitumen and paint must be removed if good ...

  • pdf, 157.55 Kb
08/04/2020

MasterProtect H380_TDS.pdf

Solvent based silane siloxane primer and penetrative water repellent protective treatment for concrete and masonry ... All surfaces to be treated should be fully cured, dry and free ...

  • pdf, 146.20 Kb
08/04/2020

MasterEmaco N 301_TDS.pdf

Single component polymer modified fairing coat and filler for pinholes ... thoroughly soaked prior to application of MasterEmaco N 301, to ensure a saturated, but surface dry condition ...

  • pdf, 146.90 Kb
08/04/2020

MasterProtect P 659_TDS.pdf

Surfaces must be clean and dry ... Use suitable methods to remove dirt, dust, oil an all other forms of contamination that could interfere with the adhesion of the primer ...

  • pdf, 144.53 Kb
08/04/2020

MasterEmaco N 307_TDS.pdf

Single component polymer modified fairing coat ... MasterEmaco N 307 should be applied to the complete area with the minimum of troweling ... Leave for a short period before final troweling ...

  • pdf, 146.87 Kb
1 to 20 of 324 results
Items per page